Hardware
Druckertyp:
Drucker:
Extruder:
Materialart:
Profil:
Software
Softwarehersteller:
Software:
Softwareversion:
Slicer:
Slicer-version:

Slicer-Parameter

Parameter Name Beschreibung
1 Layer height

This setting controls the height (and thus the total number) of the slices/layers. Thinner layers give better accuracy but take more time to print.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.30
2 First layer height

When printing with very low layer heights, you might still want to print a thicker bottom layer to improve adhesion and tolerance for non perfect build plates. This can be expressed as an absolute value or as a percentage (for example: 150%) over the default layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.35
3 Use adaptive slicing

Automatically determine layer heights by the objects topology instead of using the static value.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
4 Adaptive quality

Controls the quality / printing time tradeoff for adaptive layer generation. 0 -> fastest printing with max layer height, 100 -> highest quality, min layer height.

Art des Parameters: Integer
Maßeinheit:%
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:75
5 Match horizontal surfaces

Try to match horizontal surfaces during the slicing process. Matching is not guaranteed, very small surfaces and multiple surfaces with low vertical distance might cause bad results.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Perimeters

This option sets the number of perimeters to generate for each layer. Note that Slic3r may increase this number automatically when it detects sloping surfaces which benefit from a higher number of perimeters if the Extra Perimeters option is enabled.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:3
2 Spiral vase

This feature will raise Z gradually while printing a single-walled object in order to remove any visible seam. This option requires a single perimeter, no infill, no top solid layers and no support material. You can still set any number of bottom solid layers as well as skirt/brim loops. It won't work when printing more than an object.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Top solid layers

Number of solid layers to generate on top surfaces.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:3
2 Bottom solid layers

Number of solid layers to generate on bottom surfaces.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:3
Parameter Name Beschreibung
1 Extra perimeters if needed

Add more perimeters when needed for avoiding gaps in sloping walls.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
2 Avoid crossing perimeters

Optimize travel moves in order to minimize the crossing of perimeters. This is mostly useful with Bowden extruders which suffer from oozing. This feature slows down both the print and the G-code generation.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
3 Detect thin walls

Detect single-width walls (parts where two extrusions don't fit and we need to collapse them into a single trace).

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
4 Detect bridging perimeters

Experimental option to adjust flow for overhangs (bridge flow will be used), to apply bridge speed to them and enable fan.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
Parameter Name Beschreibung
1 Seam position

Position of perimeters starting points.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:aligned
2 External perimeters first

Print contour perimeters from the outermost one to the innermost one instead of the default inverse order.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Fill density

Density of internal infill, expressed in the range 0% - 100%

Art des Parameters: Integer
Maßeinheit:%
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:20
2 Fill pattern

Fill pattern for general low-density infill.

3 Top external infill pattern

Infill pattern for top layers. This only affects the external visible layer, and not its adjacent solid shells.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:rectilinear
4 Bottom external infill pattern

Infill pattern for bottom layers. This only affects the external visible layer, and not its adjacent solid shells.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:rectilinear
Parameter Name Beschreibung
1 Combine infill every

This feature allows to combine infill and speed up your print by extruding thicker infill layers while preserving thin perimeters, thus accuracy.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
2 Only infill where needed

This option will limit infill to the areas actually needed for supporting ceilings (it will act as internal support material). If enabled, slows down the G-code generation due to the multiple checks involved.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Fill gaps

If this is enabled, gaps will be filled with single passes. Enable this for better quality, disable it for shorter printing times.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
2 Solid infill every

This feature allows to force a solid layer every given number of layers. Zero to disable. You can set this to any value (for example 9999); Slic3r will automatically choose the maximum possible number of layers to combine according to nozzle diameter and layer height.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
3 Fill angle

Default base angle for infill orientation. Cross-hatching will be applied to this. Bridges will be infilled using the best direction Slic3r can detect, so this setting does not affect them.

Art des Parameters: Integer
Maßeinheit:°
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:45
4 Solid infill threshold area

Force solid infill for regions having a smaller area than the specified threshold.

Art des Parameters: Integer
Maßeinheit:mm²
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:70
5 Only retract when crossing perimeters

Disables retraction when the travel path does not exceed the upper layer's perimeters (and thus any ooze will be probably invisible).

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
6 Infill before perimeters

This option will switch the print order of perimeters and infill, making the latter first.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Loops (minimum)

Number of loops for the skirt. If the Minimum Extrusion Length option is set, the number of loops might be greater than the one configured here. Set this to zero to disable skirt completely.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
2 Distance from object

Distance between skirt and object(s). Set this to zero to attach the skirt to the object(s) and get a brim for better adhesion.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:6.00
3 Skirt height

Height of skirt expressed in layers. Set this to a tall value to use skirt as a shield against drafts.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
4 Minimum extrusion length

Generate no less than the number of skirt loops required to consume the specified amount of filament on the bottom layer. For multi-extruder machines, this minimum applies to each extruder.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
Parameter Name Beschreibung
1 Exterior brim width

Horizontal width of the brim that will be printed around each object on the first layer.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
2 Interior brim width

Horizontal width of the brim that will be printed inside object holes on the first layer.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
3 Brim connections width

If set to a positive value, straight connections will be built on the first layer between adjacent objects.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
Parameter Name Beschreibung
1 Generate support material

Enable support material generation.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
2 Overhang threshold

Support material will not be generated for overhangs whose slope angle (90В° = vertical) is above the given threshold. In other words, this value represent the most horizontal slope (measured from the horizontal plane) that you can print without support material. Set to a percentage to automatically detect based on some % of overhanging perimeter width instead (recommended).

Art des Parameters: Integer
Maßeinheit:° or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:60%
3 Max layer count for supports

Disable support generation above this layer. Setting this to 0 will disable this feature.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
4 Enforce support for the first

Generate support material for the specified number of layers counting from bottom, regardless of whether normal support material is enabled or not and regardless of any angle threshold. This is useful for getting more adhesion of objects having a very thin or poor footprint on the build plate.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Raft layers

The object will be raised by this number of layers, and support material will be generated under it.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Contact Z distance

The vertical distance between object and support material interface. Setting this to 0 will also prevent Slic3r from using bridge flow and speed for the first object layer.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.20
2 Pattern

Pattern used to generate support material.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:pillars
3 Pattern spacing

Spacing between support material lines.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:2.50
4 Pattern angle

Use this setting to rotate the support material pattern on the horizontal plane.

Art des Parameters: Integer
Maßeinheit:°
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
5 Interface layers

Number of interface layers to insert between the object(s) and support material.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:3
6 Interface pattern spacing

Spacing between interface lines. Set zero to get a solid interface.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
7 Support on build plate only

Only create support if it lies on a build plate. Don't create support on a print.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
8 Don`t support bridges

Experimental option for preventing support material from being generated under bridged areas.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
Parameter Name Beschreibung
1 Perimeters

Speed for perimeters (contours, aka vertical shells).

Art des Parameters: Integer
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:60
2 ➥ small

This separate setting will affect the speed of perimeters having radius <= 6.5mm (usually holes). If expressed as percentage (for example: 80%) it will be calculated on the perimeters speed setting above.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:15
3 ➥ external

This separate setting will affect the speed of external perimeters (the visible ones). If expressed as percentage (for example: 80%) it will be calculated on the perimeters speed setting above.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:50%
4 Infill

Speed for printing the internal fill.

Art des Parameters: Integer
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:80
5 ➥ solid

Speed for printing solid regions (top/bottom/internal horizontal shells). This can be expressed as a percentage (for example: 80%) over the default infill speed above.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:20
6 ➥ top solid

Speed for printing top solid layers (it only applies to the uppermost external layers and not to their internal solid layers). You may want to slow down this to get a nicer surface finish. This can be expressed as a percentage (for example: 80%) over the solid infill speed above.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:15
7 ➥ gaps

Speed for filling gaps. Since these are usually single lines you might want to use a low speed for better sticking. If expressed as percentage (for example: 80%) it will be calculated on the infill speed setting above.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:20
8 Bridges

Speed for printing bridges.

Art des Parameters: Integer
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:60
9 Support material

Speed for printing support material.

Art des Parameters: Integer
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:60
10 ➥ interface

Speed for printing support material interface layers. If expressed as percentage (for example 50%) it will be calculated over support material speed.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:100%
Parameter Name Beschreibung
1 Travel

Speed for travel moves (jumps between distant extrusion points).

Art des Parameters: Integer
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:130
Parameter Name Beschreibung
1 First layer speed

If expressed as absolute value in mm/s, this speed will be applied to all the print moves of the first layer, regardless of their type. If expressed as a percentage (for example: 40%) it will scale the default speeds.

Art des Parameters: Integer
Maßeinheit:mm/s or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:30
Parameter Name Beschreibung
1 Perimeters

This is the acceleration your printer will use for perimeters. A high value like 9000 usually gives good results if your hardware is up to the job. Set zero to disable acceleration control for perimeters.

Art des Parameters: Integer
Maßeinheit:mm/s²
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
2 Infill

This is the acceleration your printer will use for infill. Set zero to disable acceleration control for infill.

Art des Parameters: Integer
Maßeinheit:mm/s²
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
3 Bridge

This is the acceleration your printer will use for bridges. Set zero to disable acceleration control for bridges.

Art des Parameters: Integer
Maßeinheit:mm/s²
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
4 First layer

This is the acceleration your printer will use for first layer. Set zero to disable acceleration control for first layer.

Art des Parameters: Integer
Maßeinheit:mm/s²
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
5 Default

This is the acceleration your printer will be reset to after the role-specific acceleration values are used (perimeter/infill). Set zero to prevent resetting acceleration at all.

Art des Parameters: Integer
Maßeinheit:mm/s²
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Max print speed

When setting other speed settings to 0 Slic3r will autocalculate the optimal speed in order to keep constant extruder pressure. This experimental setting is used to set the highest print speed you want to allow.

Art des Parameters: Integer
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:80
2 Max volumetric speed

If set to a non-zero value, extrusion will be limited to this volumetric speed. You may want to set it to your extruder maximum. As a hint, you can read calculated volumetric speeds in the comments of any G-code file you export from Slic3r.

Art des Parameters: Integer
Maßeinheit:mm³/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Perimeter extruder

The extruder to use when printing perimeters and brim. First extruder is 1.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
2 Infill extruder

The extruder to use when printing infill.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
3 Solid infill extruder

The extruder to use when printing solid infill.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
4 Support material/raft/skirt extruder

The extruder to use when printing support material, raft and skirt.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
5 Support material/raft interface_extruder

The extruder to use when printing support material interface. This affects raft too.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
Parameter Name Beschreibung
1 Ooze prevention

During multi-extruder prints, this option will drop the temperature of the inactive extruders to prevent oozing. It will enable a tall skirt automatically and move extruders outside such skirt when changing temperatures.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
2 Temperature variation

Temperature difference to be applied when an extruder is not active. Enables a full-height "sacrificial" skirt on which the nozzles are periodically wiped.

Art des Parameters: Integer
Maßeinheit:d°C
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:-5
Parameter Name Beschreibung
1 Regions/extruders overlap

This setting applies an additional overlap between regions printed with distinct extruders or distinct settings. This shouldn't be needed under normal circumstances.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
2 Interface shells

Force the generation of solid shells between adjacent materials/volumes. Useful for multi-extruder prints with translucent materials or manual soluble support material.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Default extrusion width

Set this to a non-zero value to set a manual extrusion width. If expressed as percentage (for example: 230%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:auto(0)
2 First layer

Set this to a non-zero value to set a manual extrusion width for first layer. You can use this to force fatter extrudates for better adhesion. If expressed as percentage (for example 120%) it will be computed over first layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:200%
3 Perimeters

Set this to a non-zero value to set a manual extrusion width for perimeters. You may want to use thinner extrudates to get more accurate surfaces. If expressed as percentage (for example 200%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:default(0)
4 ➥ external

Set this to a non-zero value to set a manual extrusion width for external perimeters. If auto is chosen, a value will be used that maximizes accuracy of the external visible surfaces. If expressed as percentage (for example 200%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:auto(0)
5 Infill

Set this to a non-zero value to set a manual extrusion width for infill. You may want to use fatter extrudates to speed up the infill and make your parts stronger. If expressed as percentage (for example 90%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:default(0)
6 ➥ solid

Set this to a non-zero value to set a manual extrusion width for infill for solid surfaces. If expressed as percentage (for example 90%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:default(0)
7 ➥ top solid

Set this to a non-zero value to set a manual extrusion width for infill for top surfaces. You may want to use thinner extrudates to fill all narrow regions and get a smoother finish. If expressed as percentage (for example 90%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:default(0)
8 Support interface

Set this to a non-zero value to set a manual extrusion width for support material interface. If expressed as percentage (for example 90%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:default(0)
9 Support material

Set this to a non-zero value to set a manual extrusion width for support material. If expressed as percentage (for example 90%) it will be computed over layer height.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:default(0)
Parameter Name Beschreibung
1 Infill/perimeters overlap

This setting applies an additional overlap between infill and perimeters for better bonding. Theoretically this shouldn't be needed, but backlash might cause gaps. If expressed as percentage (example: 15%) it is calculated over perimeter extrusion width.

Art des Parameters: Double
Maßeinheit:mm or %
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:55%
Parameter Name Beschreibung
1 Bridge flow ratio

This factor affects the amount of plastic for bridging. You can decrease it slightly to pull the extrudates and prevent sagging, although default settings are usually good and you should experiment with cooling (use a fan) before tweaking this.

Art des Parameters: Double
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
Parameter Name Beschreibung
1 XY Size Compensation

The object will be grown/shrunk in the XY plane by the configured value (negative = inwards, positive = outwards). This might be useful for fine-tuning hole sizes.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
2 Resolution (deprecated)

Minimum detail resolution, used to simplify the input file for speeding up the slicing job and reducing memory usage. High-resolution models often carry more detail than printers can render. Set to zero to disable any simplification and use full resolution from input.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Complete individual objects

When printing multiple objects or copies, this feature will complete each object before moving onto next one (and starting it from its bottom layer). This feature is useful to avoid the risk of ruined prints. Slic3r should warn and prevent you from extruder collisions, but beware.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
2 Extruder clearance Radius

Set this to the clearance radius around your extruder. If the extruder is not centered, choose the largest value for safety. This setting is used to check for collisions and to display the graphical preview in the plater.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:20.00
3 Extruder clearance Height

Set this to the vertical distance between your nozzle tip and (usually) the X carriage rods. In other words, this is the height of the clearance cylinder around your extruder, and it represents the maximum depth the extruder can peek before colliding with other printed objects.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:20.00
Parameter Name Beschreibung
1 Verbode G-code

Enable this to get a commented G-code file, with each line explained by a descriptive text. If you print from SD card, the additional weight of the file could make your firmware slow down.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
2 Output filename format

You can use all configuration options as variables inside this template. For example: [layer_height], [fill_density] etc. You can also use [timestamp], [year], [month], [day], [hour], [minute], [second], [version], [input_filename], [input_filename_base].

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:[input_filename_base].gcode
Parameter Name Beschreibung
1 Post-processing scripts

If you want to process the output G-code through custom scripts, just list their absolute paths here. Separate multiple scripts on individual lines. Scripts will be passed the absolute path to the G-code file as the first argument, and they can access the Slic3r config settings by reading environment variables.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Notes

You can put here your personal notes. This text will be added to the G-code header comments.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Color

This is only used in the Slic3r interface as a visual help.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:#FFFFFF
2 Diameter

Enter your filament diameter here. Good precision is required, so use a caliper and do multiple measurements along the filament, then compute the average.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:3
3 Extrusion multiplier

This factor changes the amount of flow proportionally. You may need to tweak this setting to get nice surface finish and correct single wall widths. Usual values are between 0.9 and 1.1. If you think you need to change this more, check filament diameter and your firmware E steps.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1.00
Parameter Name Beschreibung
1 Extruder First layer

Extruder temperature for first layer. If you want to control temperature manually during print, set this to zero to disable temperature control commands in the output file.

Art des Parameters: Integer
Maßeinheit:°C
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:200
2 Extruder Other layers

Extruder temperature for layers after the first one. Set this to zero to disable temperature control commands in the output.

Art des Parameters: Integer
Maßeinheit:°C
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:200
3 Bed First layer

Heated build plate temperature for the first layer. Set this to zero to disable bed temperature control commands in the output.

Art des Parameters: Integer
Maßeinheit:°C
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
4 Bed Other layers

Bed temperature for layers after the first one.

Art des Parameters: Integer
Maßeinheit:°C
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Density

Enter your filament density here. This is only for statistical information. A decent way is to weigh a known length of filament and compute the ratio of the length to volume. Better is to calculate the volume directly through displacement.

Art des Parameters: Double
Maßeinheit:g/cm³
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
2 Cost

Enter your filament cost per kg here. This is only for statistical information.

Art des Parameters: Double
Maßeinheit:money/kg
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Keep fan always on

If this is enabled, fan will never be disabled and will be kept running at least at its minimum speed. Useful for PLA, harmful for ABS.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
2 Enable auto cooling

This flag enables the automatic cooling logic that adjusts print speed and fan speed according to layer printing time.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
Parameter Name Beschreibung
1 Min Fan speed

This setting represents the minimum PWM your fan needs to work.

Art des Parameters: Integer
Maßeinheit:%
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:35
2 Max Fan speed

This setting represents the maximum speed of your fan.

Art des Parameters: Integer
Maßeinheit:%
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:100
3 Bridges fan speed

This fan speed is enforced during all bridges and overhangs.

Art des Parameters: Integer
Maßeinheit:%
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:100
4 Disable fan for first layers

You can set this to a positive value to disable fan at all during the first layers, so that it does not make adhesion worse.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:3
Parameter Name Beschreibung
1 Enable fan if layer print time is below

If layer print time is estimated below this number of seconds, fan will be enabled and its speed will be calculated by interpolating the minimum and maximum speeds.

Art des Parameters: Integer
Maßeinheit:s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:60
2 Slow down if layer print time is below

If layer print time is estimated below this number of seconds, print moves speed will be scaled down to extend duration to this value.

Art des Parameters: Integer
Maßeinheit:s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:5
3 Min print speed

Slic3r will not scale speed down below this speed.

Art des Parameters: Double
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:10
Parameter Name Beschreibung
1 Start G-code

This start procedure is inserted at the beginning, after any printer start gcode. This is used to override settings for a specific filament. If Slic3r detects M104, M109, M140 or M190 in your custom codes, such commands will not be prepended automatically so you're free to customize the order of heating commands and other custom actions. Note that you can use placeholder variables for all Slic3r settings, so you can put a "M109 S[first_layer_temperature]" command wherever you want. If you have multiple extruders, the gcode is processed in extruder order.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:; Filament gcode
2 End G-code

This end procedure is inserted at the end of the output file, before the printer end gcode. Note that you can use placeholder variables for all Slic3r settings. If you have multiple extruders, the gcode is processed in extruder order. If Slic3r detects M104, M109, M140 or M190 in your custom codes, such commands will not be prepended automatically so you're free to customize the order of heating commands and other custom actions.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:; Filament-specific end gcode ;END gcode for filament
Parameter Name Beschreibung
1 Notes

You can put your notes regarding the filament here.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Max volumetric speed

Maximum volumetric speed allowed for this filament. Limits the maximum volumetric speed of a print to the minimum of print and filament volumetric speed. Set to zero for no limit.

Art des Parameters: Double
Maßeinheit:mm³/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Bed shape

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
2 Z offset

This value will be added (or subtracted) from all the Z coordinates in the output G-code. It is used to compensate for bad Z endstop position: for example, if your endstop zero actually leaves the nozzle 0.3mm far from the print bed, set this to -0.3 (or fix your endstop).

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Extruders

Number of extruders of the printer.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:1
2 Has heat bed

Unselecting this will suppress automatic generation of bed heating gcode.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:true
Parameter Name Beschreibung
1 G-code_flavor

Some G/M-code commands, including temperature control and others, are not universal. Set this option to your printer's firmware to get a compatible output. The "No extrusion" flavor prevents Slic3r from exporting any extrusion value at all.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:reprap
Parameter Name Beschreibung
1 Use relative E distances

If your firmware requires relative E values, check this, otherwise leave it unchecked. Most firmwares use absolute values.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
2 Use firmware retraction

This experimental setting uses G10 and G11 commands to have the firmware handle the retraction. This is only supported in recent Marlin.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
3 Use volumetric E

This experimental setting uses outputs the E values in cubic millimeters instead of linear millimeters. If your firmware doesn't already know filament diameter(s), you can put commands like 'M200 D[filament_diameter_0] T0' in your start G-code in order to turn volumetric mode on and use the filament diameter associated to the filament selected in Slic3r. This is only supported in recent Marlin.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
4 Pressure advance

When set to a non-zero value, this experimental option enables pressure regulation. It's the K constant for the advance algorithm that pushes more or less filament upon speed changes. It's useful for Bowden-tube extruders. Reasonable values are in range 0-10.

Art des Parameters: Double
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
5 Vibration limit (deprecated)

This experimental option will slow down those moves hitting the configured frequency limit. The purpose of limiting vibrations is to avoid mechanical resonance. Set zero to disable.

Art des Parameters: Double
Maßeinheit:Hz
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
6 Z full steps/mm

Set this to the number of *full* steps (not microsteps) needed for moving the Z axis by 1mm; you can calculate this by dividing the number of microsteps configured in your firmware by the microstepping amount (8, 16, 32). Slic3r will round your configured layer height to the nearest multiple of that value in order to ensure the best accuracy. This is most useful for machines with imperial leadscrews or belt-driven Z or for unusual layer heights with metric leadscrews. If you still experience wobbling, try using 4 * full_step to achieve the same motor phase pattern for every layer (important for belt driven z-axis). Set to zero to disable this experimental feature.

Art des Parameters: Double
Maßeinheit:step/mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
7 Use Set-and-wait G-code (Extruder)

If your firmware supports a set and wait gcode for temperature changes, use it for automatically inserted temperature gcode for all extruders. Does not affect custom gcode.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
8 Use Set-and-wait G-code (Bed)

If your firmware supports a set and wait gcode for temperature changes, use it for automatically inserted temperature gcode for the heatbed. Does not affect custom gcode.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Start G-code

This start procedure is inserted at the beginning, after bed has reached the target temperature and extruder just started heating, and before extruder has finished heating. If Slic3r detects M104, M109, M140 or M190 in your custom codes, such commands will not be prepended automatically so you're free to customize the order of heating commands and other custom actions. Note that you can use placeholder variables for all Slic3r settings, so you can put a "M109 S[first_layer_temperature]" command wherever you want.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:G28 ; home all axes G1 Z5 F5000 ; lift nozzle
2 End G-code

This end procedure is inserted at the end of the output file. Note that you can use placeholder variables for all Slic3r settings. If Slic3r detects M104, M109, M140 or M190 in your custom codes, such commands will not be prepended automatically so you're free to customize the order of heating commands and other custom actions.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:M104 S0 ; turn off temperature G28 X0 ; home X axis M84 ; disable motors
3 Before layer change G-code

This custom code is inserted at every layer change, right before the Z move. Note that you can use placeholder variables for all Slic3r settings as well as [layer_num], [layer_z] and [current_retraction].

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
4 After layer change G-code

This custom code is inserted at every layer change, right before the Z move. Note that you can use placeholder variables for all Slic3r settings as well as [layer_num], [layer_z] and [current_retraction].

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
5 Tool change G-code

This custom code is inserted right before every extruder change. Note that you can use placeholder variables for all Slic3r settings as well as [previous_extruder], [next_extruder], [previous_retraction] and [next_retraction].

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
6 Between objects G-code (for sequential printing)

This code is inserted between objects when using sequential printing. By default extruder and bed temperature are reset using non-wait command; however if M104, M109, M140 or M190 are detected in this custom code, Slic3r will not add temperature commands. Note that you can use placeholder variables for all Slic3r settings, so you can put a "M109 S[first_layer_temperature]" command wherever you want.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Notes

You can put your notes regarding the printer here. This text will be added to the G-code header comments.

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Nozzle diameter

This is the diameter of your extruder nozzle (for example: 0.5, 0.35 etc.)

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.50
Parameter Name Beschreibung
1 Min

This is the lowest printable layer height for this extruder and limits the resolution for adaptive slicing. Typical values are 0.1 or 0.05.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.15
2 Max

This is the highest printable layer height for this extruder and limits the resolution for adaptive slicing. Typical values are slightly smaller than nozzle_diameter.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.30
Parameter Name Beschreibung
1 Extruder offset

If your firmware doesn't handle the extruder displacement you need the G-code to take it into account. This option lets you specify the displacement of each extruder with respect to the first one. It expects positive coordinates (they will be subtracted from the XY coordinate).

Art des Parameters: String
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0x0
Parameter Name Beschreibung
1 Length

When retraction is triggered, filament is pulled back by the specified amount (the length is measured on raw filament, before it enters the extruder).

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:2.00
2 Lift Z

If you set this to a positive value, Z is quickly raised every time a retraction is triggered. When using multiple extruders, only the setting for the first extruder will be considered.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
3 Only Lift Z Above

If you set this to a positive value, Z lift will only take place above the specified absolute Z. You can tune this setting for skipping lift on the first layers.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
4 Only Lift Z Below

If you set this to a positive value, Z lift will only take place below the specified absolute Z. You can tune this setting for limiting lift to the first layers.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
5 Speed

The speed for retractions (it only applies to the extruder motor). If you use the Firmware Retraction option, please note this value still affects the auto-speed pressure regulator.

Art des Parameters: Double
Maßeinheit:mm/s
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:40.00
6 Extra length on restart

When the retraction is compensated after the travel move, the extruder will push this additional amount of filament. This setting is rarely needed.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
7 Minimum travel after retraction

Retraction is not triggered when travel moves are shorter than this length.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:2.00
8 Retract on layer change

This flag enforces a retraction whenever a Z move is done.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
9 Wipe while retracting

This flag will move the nozzle while retracting to minimize the possible blob on leaky extruders.

Art des Parameters: Boolean
Maßeinheit:
Mindestwert:false
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:true
Schrittwert:
Standardwert:false
Parameter Name Beschreibung
1 Length

When retraction is triggered before changing tool, filament is pulled back by the specified amount (the length is measured on raw filament, before it enters the extruder).

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:10.00
2 Extra length on restart

When the retraction is compensated after changing tool, the extruder will push this additional amount of filament.

Art des Parameters: Double
Maßeinheit:mm
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0.00
Parameter Name Beschreibung
1 Threads

Number of threads to use. Threads are used to parallelize long-running tasks. Optimal threads number is slightly above the number of available cores/processors.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:4
2 Distance between copies

Distance used for the auto-arrange feature of the plater.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:6
3 Extrusion axis

Use this option to set the axis letter associated to your printer's extruder (usually E but some printers use A).

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:E
4 Use native G-code arcs

This experimental feature tries to detect arcs from segments and generates G2/G3 arc commands instead of multiple straight G1 commands.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
5 Sequential Printing Priority

Set this to alter object priority for sequential printing. Objects are first sorted by priority (smaller integers print first), then by height.

Art des Parameters: Integer
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:0
Parameter Name Beschreibung
1 Random

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
2 Nearest

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
3 Aligned

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
4 Rear

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Rectilinear

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
2 Aligned Rectilinear

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
3 Grid

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
4 Triangles

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
5 Stars

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
6 Cubic

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
7 Concentric

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
8 Honeycomb

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
9 3D Honeycomb

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
10 Gyroid

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
11 Hilbert Curve

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
12 Archimedean Chords

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
13 Octagram Spiral

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 Rectilinear

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
2 Concentric

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
3 Hilbert Curve

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
4 Archimedean Chords

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
5 Octagram Spiral

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 rectilinear

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
2 rectilinear grid

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
3 honyecomb

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
4 pillars

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
Parameter Name Beschreibung
1 RepRap (Marlin/Sprinter)

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
2 Repetier

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
3 Teacup

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
4 MakerWare (MakerBot)

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
5 Sailfish (MakerBot)

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
6 Mach3/LinuxCNC

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
7 Machinekit

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
8 Smoothieware

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert:
9 No extrusion

Art des Parameters: String
Maßeinheit:
Mindestwert:
Mindestwert (Warnung):
Höchster Wert (Warnung):
Höchster Wert:
Schrittwert:
Standardwert: