8
|
baseLayerHeight
|
Base layer height
|
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | 0.05 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 1.60 |
Step value: | 0.01 |
Default value: | -1.00 |
|
9
|
areaToTaperSupportsIn
|
Maximum Area To Taper Supports In
|
When generated support structures are larger than this area, we can save time and print material while ensuring print success. We taper the support structure in from area at that point until this threshold. Once the area is smaller than this, we create support structures as columns like default.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 99999.00 |
Step value: | 0.01 |
Default value: | 350.00 |
|
10
|
areaToTaperSupportsOut
|
Minimum Area To Taper Supports Out
|
When generated support structures are smaller than this area, the base or footprint is not sturdy enough and may fall over. We taper the support structure out from original area until this threshold. Once the area is larger than this, we create support structures as columns like default (creates pencil looking structures that balance adhesion/lateral stability while limiting excess amount of footprint/support base that attaches to build plate or model material).
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 99999.00 |
Step value: | 0.01 |
Default value: | 350.00 |
|
11
|
baseLayerExtruder
|
Extruder with which to print the base layer
|
Extruder with which the entire base layer will be printed.
|
Type of parameter: |
Integer
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | |
|
12
|
baseLayerWidth
|
Base layer width
|
Force the extrusions of the model base layer to be this wide.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | 0.05 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 4.00 |
Step value: | 0.01 |
Default value: | |
|
13
|
convertSparsePulseValue
|
Convert Sparse Pulse Value
|
Offset value in mm to reduce small sparse areas by. We pulse in and then out to identify sparse areas in the geometry that will succeed better as solid regions.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 50.00 |
Step value: | 0.01 |
Default value: | 0.00 |
|
14
|
doSmartZipper
|
Smart Zipper
|
Select to enable smart zipper placement algorithm. This minimizes conspicuous zippers to improve print appearance by starting shell at most concave point of the polygon.
|
Type of parameter: |
Boolean
|
Unit of measurement: | |
Minimum value: | false |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | true |
Step value: | |
Default value: | false |
|
15
|
doStickyMaterialSwitching
|
doStickyMaterialSwitching
|
When moving up in Z-height, print with the last-used material first to minimize toolchanges.
|
Type of parameter: |
Boolean
|
Unit of measurement: | |
Minimum value: | false |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | true |
Step value: | |
Default value: | false |
|
16
|
doZHopAndRetractCombo
|
doZHopAndRetractCombo
|
Combine z hops and filament retracts into one move to battle stringiness.
|
Type of parameter: |
Boolean
|
Unit of measurement: | |
Minimum value: | false |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | true |
Step value: | |
Default value: | false |
|
17
|
horizontalInset
|
horizontalInset
|
An inset in the x-y plane. Increasting this values increases your tolerances.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 0.0 |
|
18
|
lowSpeedShellMin
|
Low Speed Shell Minimum
|
Minimum area threshold before shells are printed with low_speed_shells extrusion label.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 100.00 |
Step value: | 0.01 |
Default value: | 0.00 |
|
19
|
maxSmartAngleDegs
|
Maximum Smart Zipper Angle in Degrees
|
Maximum concave angle in degrees for smart zipper placement. If there is no angle smaller than this value on the polygon, smart zipper will not figure placement.
|
Type of parameter: |
Integer
|
Unit of measurement: | ° |
Minimum value: | 0 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 180 |
Step value: | 1 |
Default value: | 179 |
|
20
|
minimumMoveDistance
|
minimumMoveDistance
|
Minimum distance any move can be.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 1.00 |
Step value: | 0.01 |
Default value: | 0.00 |
|
21
|
minPrintableArea
|
minPrintableArea
|
Minimum area such that its shell maintains structural stability when printed.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 5.0 |
|
22
|
minSparseRegionArea
|
Minimum Sparse Region Area
|
Smallest area sparse region can be before we convert into solid.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 99999.00 |
Step value: | 0.01 |
Default value: | 0.00 |
|
23
|
minSplitChunkPrintableArea
|
minSplitChunkPrintableArea
|
Minimum required area for a split chunk to be printed.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 1.0 |
|
24
|
pauseHeights
|
pauseHeights
|
These are the heights to pause at.
|
Type of parameter: |
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | [] |
|
25
|
useRelativeExtruderPositions
|
Use Relative Extruder Positions
|
Use relative extruder positions for motors in Json Toolpath output only (never GCode). Absolute position and relative positions have different outcomes through Firmware (2018-05-17). Useful to get around a blobbing on restart from pause issue, but in future this key may possibly be deprecated.
|
Type of parameter: |
Boolean
|
Unit of measurement: | |
Minimum value: | false |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | true |
Step value: | |
Default value: | false |
|
26
|
verticalAggregationCleanupDistance
|
verticalAggregationCleanupDistance
|
Distance to inward pulse regions generated by the vertical aggregator.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 0.0 |
|
27
|
xScale
|
xScale
|
Scale correction in X. 1.0 is no change.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 1.0 |
|
28
|
yScale
|
yScale
|
Scale correction in Y. 1.0 is no change.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 1.0 |
|
29
|
zScale
|
zScale
|
Scale correction in Z. 1.0 is no change.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 1.0 |
|
30
|
startPosition
|
Start Position
|
Initial position of all axes of the bot.
|
Type of parameter: |
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | |
|
31
|
doSplitLongMoves
|
Split Long Moves
|
If both a tight curve and part of a long, straight line are included in a Dynamic Speed Detection Window, the average change in degrees per millimeter may not be large enough to trigger a Dynamic Speed slowdown. This setting fixes this problem by splitting each long move into sections and treating them as separate moves. When set to true, every long move will be split into segments of the length set in the splitMinimumDistance setting. If splitting a long move does not trigger a Dynamic Speed change, the segments will be recombined. If you choose to split long moves into small segments, be aware that they may increase the size of your print file.
|
Type of parameter: |
Boolean
|
Unit of measurement: | |
Minimum value: | false |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | true |
Step value: | |
Default value: | false |
|
32
|
doZHopOnToggle
|
Do Z-Hop on Extruder Toggle
|
Whether or not we want to do a z-hop when toggling extruders.
|
Type of parameter: |
Boolean
|
Unit of measurement: | |
Minimum value: | false |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | true |
Step value: | |
Default value: | false |
|
33
|
maxConnectionLength
|
Maximum Connection Length
|
Maximum length of an extrusion made to avoid retraction. If avoiding a retraction would require a longer extrusion, we will retract and go to the closest object instead.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | 0.0 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 50.0 |
Step value: | 0.5 |
Default value: | 10.0 |
|
34
|
minfillHighHeatCapacityExtrusionProfile
|
minfillHighHeatCapacityExtrusionProfile
|
Extrusion Profile to use for low heat capacity thin outline structures.
|
Type of parameter: |
String
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | sparse |
|
35
|
minfillLowHeatCapacityExtrusionProfile
|
minfillLowHeatCapacityExtrusionProfile
|
Extrusion Profile to use for high heat capacity thick outline structures.
|
Type of parameter: |
String
|
Unit of measurement: | |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | halfVolumeInfill |
|
36
|
supportIslandAverageWidthRatio
|
Support Island Average Width Ratio
|
This is a ratio of 2 x area divided by perimeter (loop distance) for our support islands. When this perimeter is large while the area is small, it means the shape is thin and may fail. In terms of our tapered support algorithm, we do not want to morph or change the shape when our starting polygon is thin because portions underneath these will morph away, and not receive supports when they require them.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | 0.0 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 5.0 |
Step value: | 1.0 |
Default value: | 7.0 |
|
37
|
supportMinRegionArea
|
Support Minimum Region Area
|
Anything smaller than this area gets expanded to a printable size roughly corresponding to 2 beadwidths so at least an enclosed shell can be extruded. This value is what determines how much cascading effect our supports have. Being that supports are drawn top down, the larger this value is, the thicker all downstream supports become through ripple effect.
|
Type of parameter: |
Integer
|
Unit of measurement: | |
Minimum value: | 0 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 100 |
Step value: | 1 |
Default value: | 10 |
|
38
|
minSpeedMultiplier
|
Minimum Speed Multiplier
|
This setting multiplied by the base feedrates set in your extrusion profiles equals your minimum extrusion speed. Layers slowed down by the minLayerDuration setting will not print slower than the speed set here. Feedrates slowed down by the Dynamic Speed settings will not be affected by this setting.
|
Type of parameter: |
Double
|
Unit of measurement: | |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 1.00 |
Step value: | 0.01 |
Default value: | |
|
39
|
minThickInfillImprovement
|
Minimal Thick Infill Improvement
|
Minimum reduction in total area required for adding a thick sparse infill layer.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | |
Step value: | |
Default value: | 1.0 |
|
40
|
splitMinimumDistance
|
Split Minimum Distance
|
When doSplitLongMoves is set to true, long moves will be split into segments of the length specified here.
|
Type of parameter: |
Double
|
Unit of measurement: | mm |
Minimum value: | 0.00 |
Minimum value (Warning): | |
Maximum value (Warning): | |
Maximum value: | 5.00 |
Step value: | 0.10 |
Default value: | |
|